|
345344568
|
0419400
|
2021-06-03
|
164 SAWYER LOOP, WINONA, MS, 38967
|
|
| Inspection Type |
Referral
|
| Scope |
Partial
|
| Safety/Health |
Safety
|
| Close Conference |
2021-06-25
|
| Emphasis |
N: AMPUTATE
|
| Case Closed |
2023-03-29
|
Related Activity
| Type |
Referral |
| Activity Nr |
1773438 |
| Safety |
Yes |
|
Violation Items
| Citation ID |
01001 |
| Citaton Type |
Serious |
| Standard Cited |
19100147 C01 |
| Issuance Date |
2021-07-28 |
| Abatement Due Date |
2021-08-26 |
| Current Penalty |
3000.0 |
| Initial Penalty |
5461.0 |
| Final Order |
2021-08-30 |
| Nr Instances |
1 |
| Nr Exposed |
4 |
| Related Event Code (REC) |
Referral |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(1): Energy control program. The employer shall establish a program consisting of energy control procedures, employee training and periodic inspections to ensure that before any employee performs any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative. (a) Sawmill - On or about June 3, 2021 the employer did not have an energy control program for employees that perform servicing and maintenance on equipment such as but not limited to, Head Saw, Edger, conveyors, and Chipper with energy control procedures, documented training, and periodic inspections for employees that maintain the machinery exposing employees to caught-in and struck-by hazards. |
|
| Citation ID |
01002 |
| Citaton Type |
Serious |
| Standard Cited |
19100219 C04 I |
| Issuance Date |
2021-07-28 |
| Abatement Due Date |
2021-08-19 |
| Current Penalty |
2575.0 |
| Initial Penalty |
4681.0 |
| Final Order |
2021-08-30 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(c)(4)(i): Projecting shaft ends shall present a smooth edge and end and shall not project more than one-half the diameter of the shaft unless guarded by nonrotating caps or safety sleeves: (a) Edger Tail Conveyor - On or about June 3, 2021 the employer did not guard a rotating shaft. Employees were exposed to a caught-in hazard. |
|
| Citation ID |
01003 |
| Citaton Type |
Serious |
| Standard Cited |
19100265 E05 II A |
| Issuance Date |
2021-07-28 |
| Abatement Due Date |
2021-08-19 |
| Current Penalty |
2575.0 |
| Initial Penalty |
4681.0 |
| Final Order |
2021-08-30 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Related Event Code (REC) |
Referral |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.265(e)(5)(ii)(a): The top and the openings in end and side frames of edgers shall be adequately guarded and gears and chains shall be fully housed. Guards may be hinged or otherwise arranged to permit oiling and the removal of saws. (a) Edger - On or about June 3, 2021 the employer did not guard the drive unit exposing employees to a caught-in hazard. |
|
| Citation ID |
02001 |
| Citaton Type |
Serious |
| Standard Cited |
19100265 C04 IV |
| Issuance Date |
2021-07-28 |
| Abatement Due Date |
2021-08-19 |
| Current Penalty |
3400.0 |
| Initial Penalty |
6242.0 |
| Final Order |
2021-08-30 |
| Nr Instances |
1 |
| Nr Exposed |
3 |
| Related Event Code (REC) |
Referral |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.265(c)(4)(iv): Elevated platform(s), 4 feet or more from the floor level, were not provided with a standard railing. (a) Edger Tail Conveyor - On or about June 3, 2021 the employer did not guard the end of the catwalk with standard railing exposing employees to a fall from heights greater than 4 feet to the concrete below. The Winona Hardwood, Inc. was previously cited for a violation of this occupational safety and health standard or its equivalent standard 29 CFR 1910.265(c)(4)(iv), which was contained in OSHA inspection number 1382004, citation number 01, item number 002 and was affirmed as a final order on 7/29/2019, with respect to a workplace located at 164 Sawyer Loop Winona, MS 38967. |
|
| Citation ID |
02002 |
| Citaton Type |
Serious |
| Standard Cited |
19100265 C18 I |
| Issuance Date |
2021-07-28 |
| Abatement Due Date |
2021-08-19 |
| Current Penalty |
6000.0 |
| Initial Penalty |
10922.0 |
| Final Order |
2021-08-30 |
| Nr Instances |
1 |
| Nr Exposed |
2 |
| Related Event Code (REC) |
Referral |
| Gravity |
10 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.265(c)(18)(i): Means were not provided to guard against accidental injury to personnel at conveyor transfer, loading, or discharge point(s). (a) Edger Tail Conveyor - On or about June 3, 2021 the employer did not guard the belt and tail end drum of the conveyor, exposing employees to a caught-in hazard. (b) Edger Tail Conveyor - On or about June 3, 2021 the employer did not install an emergency stop on the conveyor, exposing employees to a caught-in hazard. The Winona Hardwood, Inc. was previously cited for a violation of this occupational safety and health standard or its equivalent standard 29 CFR 1910.265(c)(18)(i), which was contained in OSHA inspection number 1382004, citation number 01, item number 003 and was affirmed as a final order on 7/29/2019, with respect to a workplace located at 164 Sawyer Loop Winona, MS 38967. |
|
|
|
343820049
|
0419400
|
2019-03-01
|
164 SAWYER LOOP, WINONA, MS, 38967
|
|
| Inspection Type |
Planned
|
| Scope |
Complete
|
| Safety/Health |
Safety
|
| Close Conference |
2019-03-20
|
| Emphasis |
P: AMPUTATE, N: AMPUTATE
|
| Case Closed |
2019-07-29
|
Violation Items
| Citation ID |
01001 |
| Citaton Type |
Serious |
| Standard Cited |
19100219 C02 I |
| Issuance Date |
2019-06-28 |
| Abatement Due Date |
2019-07-16 |
| Current Penalty |
2028.6 |
| Initial Penalty |
3381.0 |
| Final Order |
2019-07-29 |
| Nr Instances |
1 |
| Nr Exposed |
5 |
| Gravity |
1 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.219(c)(2)(i): All exposed part(s) of horizontal shafting seven (7) feet or less from floor or working platform were not protected by stationary casing(s) enclosing shafting completely or by trough(s) enclosing sides and top or sides and bottom of shafting. a. Pine Mill - On or about March 18, 2019 the power shaft for the carriage electric motor was not guarded; entanglement hazard. |
|
| Citation ID |
01002 |
| Citaton Type |
Serious |
| Standard Cited |
19100265 C04 IV |
| Issuance Date |
2019-06-28 |
| Abatement Due Date |
2019-07-16 |
| Current Penalty |
2704.8 |
| Initial Penalty |
4508.0 |
| Final Order |
2019-07-29 |
| Nr Instances |
1 |
| Nr Exposed |
1 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.265(c)(4)(iv): Elevated platform(s), 4 feet or more from the floor level, were not provided with a standard railing. a. Hardwood Mill - On or about March 18, 2019 the oil platform for the slasher/cutup saw did not have a guardrail at the oil reservoir. The saw operator was exposed to a 7 foot fall onto dirt when checking the reservoir oil level. |
|
| Citation ID |
01003 |
| Citaton Type |
Serious |
| Standard Cited |
19100265 C18 I |
| Issuance Date |
2019-06-28 |
| Abatement Due Date |
2019-07-16 |
| Current Penalty |
3381.6 |
| Initial Penalty |
5636.0 |
| Final Order |
2019-07-29 |
| Nr Instances |
1 |
| Nr Exposed |
5 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.265(c)(18)(i): Means were not provided to guard against accidental injury to personnel at conveyor transfer, loading, or discharge point(s). a. Pine Mill Stacker, Green Chain - On or about March 18, 2019 the stacker outside chain and sprockets where employees lift and remove the boards were not guarded. An employee finger could get caught in the chain and sprocket when removing boards from the stacker. |
|
|
|
339100414
|
0419400
|
2013-06-05
|
164 SAWYER LOOP, WINONA, MS, 38967
|
|
| Inspection Type |
Monitoring
|
| Scope |
Records
|
| Safety/Health |
Safety
|
| Close Conference |
2013-06-05
|
| Case Closed |
2013-06-10
|
Related Activity
| Type |
Complaint |
| Activity Nr |
816976 |
| Safety |
Yes |
|
| Type |
Inspection |
| Activity Nr |
906122 |
| Safety |
Yes |
|
|
|
339061228
|
0419400
|
2013-05-08
|
164 SAWYER LOOP, WINONA, MS, 38967
|
|
| Inspection Type |
Complaint
|
| Scope |
Partial
|
| Safety/Health |
Safety
|
| Close Conference |
2013-05-08
|
| Emphasis |
L: EISAOF, L: EISAX, N: AMPUTATE
|
| Case Closed |
2013-06-14
|
Related Activity
| Type |
Complaint |
| Activity Nr |
816976 |
| Safety |
Yes |
|
Violation Items
| Citation ID |
01001 |
| Citaton Type |
Serious |
| Standard Cited |
19100147 C01 |
| Issuance Date |
2013-05-21 |
| Abatement Due Date |
2013-06-24 |
| Current Penalty |
1200.0 |
| Initial Penalty |
2000.0 |
| Final Order |
2013-05-29 |
| Nr Instances |
1 |
| Nr Exposed |
2 |
| Gravity |
5 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1910.147(c)(1): Energy control program. The employer shall establish a program consisting of energy control procedures, employee training and periodic inspections to ensure that before any employee performs any servicing or maintenance on a machine or equipment where the unexpected energizing, startup or release of stored energy could occur and cause injury, the machine or equipment shall be isolated from the energy source and rendered inoperative. Sawmill - On or about May 08, 2013 the facility did not have a written energy control program that has equipment listed, specific lock out procedures to deenergize the equipment, person/s responsible for conducting periodic inspections and certification of training of affected and authorized employees that is related to their specific machinery. Employees operated and performed maintenance on chipper, saws and conveyors. |
|
| Citation ID |
02001 |
| Citaton Type |
Other |
| Standard Cited |
19040029 A |
| Issuance Date |
2013-05-21 |
| Abatement Due Date |
2013-06-17 |
| Current Penalty |
240.0 |
| Initial Penalty |
400.0 |
| Final Order |
2013-05-29 |
| Nr Instances |
1 |
| Nr Exposed |
14 |
| FTA Current Penalty |
0.0 |
| Citation text line |
29 CFR 1904.29(a): Basic requirement. You must use OSHA 300, 300-A, and 301 forms, or equivalent forms, for recordable injuries and illnesses. The OSHA 300 form is called the Log of Work-Related Injuries and Illnesses, the 300-A is the Summary of Work-Related Injuries and Illnesses, and the OSHA 301 form is called the Injury and Illness Incident Report. Sawmill - On or about May 08, 2013 facility did not keep a Log of Work-Related Injuries and Illnesses, OSHA form 300 and Summary of Work-Related Injuries and Illnesses, OSHA form 300-A. An workplace employee accident with an OSHA recordable employee injury occurred in 2012. This case was not recorded on injury and illness log for 2012 and the 2012 annual summary. |
|
|
